How to install graco car seat straps




















Although it may seem easy, you must understand how. It is best to read the manual carefully before installing a car seat for safety reasons. The most important thing here is that it is correctly installed to protect your child in an accident or emergency stop. Make sure not only the installation method itself — make this unique task with Graco car seats can be quickly done in three steps. Both methods are safe.

Please read and understand this manual before you install or use this child restraint. Now below, you can see details of steps on how to install a Graco car seat. Please follow carefully. Tether Strap Stored at Top. Put a tether hook on either side of the plastic bar on the car seat. Set the car seat in a reclining position.

Car seat should face rear-ward in vehicle back seat. Ideally, the base has as flat an installation as possible. Verify the indicator level. Level ground is required for the vehicle. The car seat should indicate that it is Level. Once the blue rectangle completely encloses the bubble, it must be fully retracted. Make sure the ties are tight.

Examine the indicator of Level. There must be no bubble extending beyond the blue zone. Set the seat in the reclining position. If your car seat reclines in any of the first, second, or third positions, it will be more comfortable.

Ensure the car seat is oriented rearward in the back seat. In the back seat of the vehicle, place rear-facing. Verify the indicator of Level. Ensure the vehicle is Level. Once the bubble is within that zone, recline the chair. Ensure the seat belt is properly routed. The rear-facing seat belt should be threaded through the blue labeled path and out the opposite end. Secure with a buckle. Ensure that the belt lies flat and does not twist.

Note: If the seat pad covers the vehicle seat belt path, it may be easier to route it by lifting the seat pad. If possible, route the vehicle seat belt in front of the steering wheel.

Make sure the seatbelt is locked. When it clicks, you are done. The belt should lock once you slowly pull it out. Make sure the car seat is firmly clamped down in the middle. Feed slack back into the retractor while tightening the shoulder belt. Check the tightness of the screw. Pull the vehicle seat belt from the sides of the seat, and slide the car seat side-to-side and front-to-back.

Verify the level indicator. Level ground is required for all vehicles. Make sure the car seat is Level. Make sure the bubble exists within the blue zone. You may need to adjust the seat. Disconnect the top tether strap from its storage location. Remove the tether from the seat and lay it flat. Make sure the car seat is adjusted. In the fourth, fifth, or sixth recline position, place the car seat.

Install the car seat facing forward in the back seat of the vehicle. Make sure the base lies flat against the vehicle seat. It is not allowed to twist the latch straps at the lower anchors. To tighten through the Belt Path slit on the Pad, you may need to do so. Tether the top of the bike.

Lift the tether lock to extend the top rope. Fix the strap at the top of the helmet. Grab the sides of the car seat where the LATCH straps are located and slide it side to side and front to back. Unhook the top tether strap from the storage compartment. Install the forward-facing car seat in the back seat of the vehicle. Seat the child forward-facing in the car. As much as possible, the base should fit flat upon the vehicle seat.

Attach the seatbelt to the vehicle. This convertible car seat keeps your baby safe and secure while you journey around. While the packaging may seem like a daunting task, this item is simple to install, use and put away. Read On…. Depending on which model you own, the Graco convertible car seats have an average lifespan of 6 to 10 years.

The expiration date of a Graco car seat is labeled at the bottom. The only assembly needed for a Graco convertible car seat is joining the cup holders. Check your car seat instruction manual to learn how to install the cup holders on your car seat. Alternatively, you can find instructions on how to remove your car seat cover in your instruction manual. Generally, Graco convertible seat covers can be washed in a washing machine, so you can just throw them in the washer.

To get the buckle and harness clean, use warm water.



0コメント

  • 1000 / 1000